Microphones

Experience exceptional sound quality with the Shure MX202BP/O Overhead Omni Gooseneck (R183B) Inc PreAmp. These small yet powerful microphones deliver accurate audio reproduction with their wide dynamic range and frequency response. Fitted with the R183B Omnidirectional Mic Capsule, these overhead condenser microphones produce detailed sound across the entire audio spectrum.The balanced, transformerless output ensures reduced noise over long cable runs, allowing for crystal-clear audio capture even in demanding environments. The included plate surface mount preamp adds versatility and convenience, while the sleek black finish seamlessly blends into any setting.With a flexible four-inch gooseneck and a generous 30-foot cable, the MX202BP/O is designed for professional audio installations where quality and discretion are paramount. Whether used for live performances, recording studios, or conference settings, these microphones provide accurate sound reproduction with minimum RF interference and electromagnetic hum.Elevate your audio setup with the Shure MX202BP/O Overhead Omni Gooseneck (R183B) Inc PreAmp and discover the true potential of high-quality sound capture.Product Specifications General Frequency Response: 50 to 17,000 Hz Output Impedance: EIA Rated at 150 Ω (180 Ω actual) Sensitivity (At 1,000 Hz, open circuit voltage*) with additional cartridges: Cardioid: –35.0 dBV/Pa (17.8 mV) Supercardioid: –33.5 dBV/Pa (21.1 mV) Omnidirectional: –27.5 dBV/Pa (42.2 mV) Maximum SPL (1 kHz at 1% THD, 1 kΩ load) with additional cartridges: Cardioid: 124.2 Supercardioid: 122.7 dB Omnidirectional: 116.7 dB Equivalent Output Noise (A-weighted) with additional cartridges: Cardioid: 28.0 dB SPL Supercardioid: 26.5 dB SPL Omnidirectional: 20.5 dB SPL Signal to Noise Ratio (referenced at 94 dB SPL) with additional cartridges: Cardioid: 66.0 Supercardioid: 67.5 dB Omnidirectional: 73.5 dB Dynamic Range at 1 kΩ Load: 96.2 dB Common Mode Rejection: 45.0 dB minimum Preamplifier Output Clipping Level (1% THD): –6.0 dBV (0.5 V) Polarity: Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output connector. Power Requirements: 11 to 52 Vdc phantom, 2.0 mA Physical & Dimensions Operating Temperature Range: –18° C to 57° C (0° F to 135° F) Relative Humidity: 0 to 95% Dimensions: Length – 144.5mm (5.69”), Width – 11.7mm (0.46”)

Read more less

Experience the unparalleled performance of the Shure BETA 56A Close Drum Mic for Snare and Drum with Shock Mount. This dynamic microphone is meticulously crafted to elevate your live performances with precision, reliability, and ruggedness synonymous with the Shure brand.🎤 Delve into a world of superior sound quality with the tailored frequency response specifically engineered for drums, amplified instruments, and horns. The uniform supercardioid pick-up pattern ensures maximum gain before feedback and impeccable off-axis sound rejection, allowing your instrument to shine amidst even the loudest environments.🎶 Featuring a neodymium magnet for heightened sensitivity and increased output, this microphone captures the nuances of your performance with exceptional clarity. The advanced pneumatic shock mount system effectively minimises mechanical noise and vibrations, ensuring a pristine audio output every time.💪 Built to withstand the demands of live performances, the dent-resistant steel mesh grille and enamel-coated die-cast metal construction of the BETA 56A guarantee durability and longevity, even in the face of wear and tear.🎚️ Experience unparalleled flexibility and ease of use with the integrated swivel-mount, dynamic locking system, and XLR connector. The compact design reduces stage clutter, allowing you to focus on your craft without distraction.🥁 Elevate your sound to new heights with the Shure BETA 56A Close Drum Mic - where reliability, precision, and performance converge to deliver a true masterpiece in live audio reproduction.Product Specifications Cartridge Type: Dynamic (moving coil) Frequency Response: 50 to 16,000 Hz Polar Pattern: Supercardioid Output Impedance: 150 Ω Sensitivity (at 1kHz, open circuit voltage): −51 dBV/Pa (2.8 mV) 1 Pascal=94 dB SPL Polarity: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 Weight: Net: 0.468 lg (1.6 lbs) Connector: Three-pin professional audio (XLR), male

Read more less

Experience the unparalleled quality and performance of the Shure BETA 52A Bass Drum (Stand Mount Type) Dynamic Supercardioid Mic. Crafted to meet the exacting demands of professional musicians, this microphone is meticulously designed to capture the deep, punchy sound of kick drums and bass instruments with precision and clarity.🎤 Boasting a tailored frequency response specifically for kick drums and bass, the Beta 52A ensures that every beat is reproduced with exceptional detail and accuracy. The supercardioid design provides maximum isolation from other onstage sounds, allowing your bass instruments to take centre stage without interference.🎤 With its ability to handle high sound pressure levels, the Beta 52A is the perfect choice for capturing the raw power and energy of live performances. Whether you're miking up a kick drum, bass amp, or acoustic bass, this microphone delivers studio-quality performance both on stage and in the studio.🎤 The hardened steel mesh grille of the Beta 52A is not only durable but also ensures resistance to wear and abuse, making it a reliable companion for countless performances. The advanced pneumatic shock mount system minimises mechanical noise and vibration, guaranteeing a clean and professional sound every time.🎤 Designed for reliability, the Beta 52A features a neodymium magnet for a high signal-to-noise ratio output and low sensitivity to varying load impedance. With legendary Shure quality and reliability, you can trust that the Beta 52A will consistently deliver outstanding performance, night after night.🎤 Elevate your sound and capture the full impact of your bass instruments with the Shure BETA 52A Bass Drum (Stand Mount Type) Dynamic Supercardioid Mic. Experience the professional quality and durability that sets Shure apart, and take your performances to the next level.Product Specifications General Frequency Response: 20 Hz – 10 kHz Frequency Response: Tailored Sensitivity: -64.00 dBV/Pa – 0.60 mV/Pa Sound Pressure: 174 dB dB Transducer Type: Dynamic Polar Pattern: Supercardioid Switchable low cut: No Connectors: XLR Attenuator: No Interchangeable Capsule: No Main Functionality: Performance Headphone Output: No Cartridge: Fixed Physical & Dimensions Weight: 605g Height: 162.7mm Width: 95.25mm Depth: 113mm

Read more less

Experience the unparalleled excellence of the Shure BETA 91A Kick Drum (Boundary Type) Condenser Mic. Crafted with precision engineering, this microphone stands as a beacon of innovation in the realm of sound capture.🎤 The BETA 91A is the ultimate tool for kick drums, meticulously designed to deliver a powerful low-end response like no other. Its half-cardioid condenser boundary microphone, complete with an integrated XLR preamplifier, ensures a seamless audio performance tailored for bass frequency applications.🎶 Unleash studio-quality sound with unmatched clarity, even in high-pressure environments, thanks to its superior attack and punch. The two-position contour switch allows you to customise the sound signature according to your needs, providing versatility that elevates your musical creations to new heights.🔊 Maximise efficiency and minimise clutter with the low-profile design that seamlessly integrates the preamplifier and XLR connector. With a frequency response specifically tailored for kick drum and low-frequency applications, the BETA 91A promises maximum gain-before-feedback and rejection of off-axis sound – a true testament to its engineering excellence.✨ Elevate your audio experience with the Shure BETA 91A Kick Drum Condenser Mic – where precision meets passion, and every beat resonates with unparalleled clarity and power.Product Specifications General Frequency Response: 20 Hz – 20 kHz Frequency Response: Tailored Sensitivity: -48.50 dBV/Pa – 3.80 mV/Pa Equivalent Selfnoise: 29,5 dB(A) Sound Pressure: 155 dB dB Transducer Type: Condenser Polar Pattern: Halfcardioid Switchable low cut: No Connectors: XLR Attenuator: No Interchangeable Capsule: No Main Functionality: Performance Headphone Output: No Requires Phantom Power: 11 - 52 VDC Cartridge: Fixed Physical & Dimensions Weight: 470 g

Read more less

Experience the industry-standard in professional audio with the Shure SM57 Dynamic Cardioid Instrument/Vocal Microphone. Renowned for its exceptional quality and versatility, the SM57 is the go-to choice for musicians, sound engineers, and recording artists worldwide.🎤 Capture the pure essence of your sound: With its contoured frequency response, this microphone ensures clean and precise pick-up, delivering rich, natural instrument and vocal reproduction.🎶 Bring your performances to life: Whether you're miking up your guitar amp, bass amp, saxophone, trumpet, or drums, the SM57 excels in reproducing the true character of your instrument, making it perfect for both live stages and studio recording.🔊 Cut through the mix effortlessly: The uniform cardioid pickup pattern isolates the primary sound source, reducing background noise and capturing your performance with exceptional clarity and definition.🎛️ Built to endure the demands of professional use: Featuring a robust pneumatic shock-mount system and constructed from die-cast steel, this microphone is extremely durable and reliable even under the heaviest of applications.Unleash your creativity and elevate your sound with the legendary Shure SM57 Dynamic Cardioid Microphone. Your performances deserve nothing less than the best.Product Specifications General Frequency Response: 40 Hz – 15 kHz Frequency Response: Tailored Sensitivity: -56.00 dBV/Pa – 1.60 mV/Pa Transducer Type: Dynamic Polar Pattern: Cardioid Switchable low cut: No Connectors: XLR Attenuator: No Interchangeable Capsule: No Main Functionality: Performance Headphone Output: No Cartridge: Fixed Impedance: Rated impedance is 150Ω (310Ω actual) for connection to microphone inputs rated low impedance. Case: Dark gray, enamel-painted, die-cast steel with a polycarbonate grille and a stainless steel screen. Physical & Dimensions Weight: 284g Height: 157mm Width: 32mm Depth: 32mm

Read more less